NTD25P03L, STD25P03L
SAFE OPERATING AREA
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain ? to ? source voltage and
drain current that a transistor can handle safely when it is
forward biased. Curves are based upon maximum peak
junction temperature and a case temperature (T C ) of 25 ° C.
Peak repetitive pulsed power limits are determined by using
the thermal response data in conjunction with the procedures
discussed in AN569, “Transient Thermal Resistance ?
General Data and Its Use.”
Switching between the off ? state and the on ? state may
traverse any load line provided neither rated peak current
(I DM ) nor rated voltage (V DSS ) is exceeded, and that the
transition time (t r , t f ) does not exceed 10 m s. In addition the
total power averaged over a complete switching cycle must
not exceed (T J(MAX) ? T C )/(R q JC ).
A power MOSFET designated E ? FET can be safely used
in switching circuits with unclamped inductive loads. For
reliable operation, the stored energy from circuit inductance
dissipated in the transistor while in avalanche must be less
than the rated limit and must be adjusted for operating
conditions differing from those specified. Although industry
practice is to rate in terms of energy, avalanche energy
capability is not a constant. The energy rating decreases
non ? linearly with an increase of peak current in avalanche
and peak junction temperature.
Although many E ? FETs can withstand the stress of
drain ? to ? source avalanche at currents up to rated pulsed
current (I DM ), the energy rating is specified at rated
continuous current (I D ), in accordance with industry
custom. The energy rating must be derated for temperature
as shown in the accompanying graph (Figure 12). Maximum
energy at currents below rated continuous I D can safely be
assumed to equal the values indicated.
100
V GS = ? 20 V
SINGLE PULSE
200
180
I D = ? 20 A
10
1
T C = 25 ° C
100 m s
1 ms
10 ms
dc
160
140
120
100
80
60
0.1
0.1
R DS(on) LIMIT
THERMAL LIMIT
PACKAGE LIMIT
1
10
100
40
20
0
25
50
75
100
125
150
? V DS , DRAIN ? TO ? SOURCE VOLTAGE (VOLTS)
Figure 11. Maximum Rated Forward Biased
Safe Operating Area
T J , STARTING JUNCTION TEMPERATURE ( ° C)
Figure 12. Maximum Avalanche Energy versus
Starting Junction Temperature
http://onsemi.com
6
相关PDF资料
NTD2955PT4G MOSFET P-CH 60V 12A DPAK
NTD3055-094G MOSFET N-CH 60V 12A DPAK
NTD3055-150T4 MOSFET N-CH 60V 9A DPAK
NTD3055L104 MOSFET N-CH 60V 12A DPAK
NTD3055L170-001 MOSFET N-CH 60V 9A IPAK
NTD30N02T4 MOSFET N-CH 24V 30A DPAK
NTD32N06LT4G MOSFET N-CH 60V 32A DPAK
NTD32N06T4G MOSFET N-CH 60V 32A DPAK
相关代理商/技术参数
NTD25P03LG 功能描述:MOSFET -30V -25A P-Channel RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS(导通):0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
NTD25P03LG 制造商:ON Semiconductor 功能描述:P CHANNEL MOSFET -30V -25A D-PAK 制造商:ON Semiconductor 功能描述:P CHANNEL MOSFET, -30V, -25A, D-PAK
NTD25P03LRL 功能描述:MOSFET -30V -25A P-Channel RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS(导通):0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
NTD25P03LRLG 功能描述:MOSFET PFET 30V 25A LL TR RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS(导通):0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
NTD25P03LT4 功能描述:MOSFET -30V -25A P-Channel RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS(导通):0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
NTD25P03LT4G 功能描述:MOSFET -30V -25A P-Channel RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS(导通):0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
NTD25P03LT4G 制造商:ON Semiconductor 功能描述:P CHANNEL MOSFET -30V 25A D-PAK
NTD25P03LT4G-CUT TAPE 制造商:ON 功能描述:NTD Series P-Channel 30 V 51 mOhm 75 W Tab Mount Power MOSFET - TO-252